Conduit PDX-2
[ COMING SOON ]Power your entire Eurorack from a laptop charger - studio-grade silence in 4HP
TECHNICAL SPECIFICATIONS
Overview
Ditch the bulky brick transformer. The Conduit PDX-2 powers your entire Eurorack case from any USB-C laptop charger - with studio-grade performance in just 4HP.
At 35mm deep, it delivers massive clean power (3A on +12V, 1.5A on -12V) while staying completely silent. No audible whine, no interference with your audio signals. Enough power for 15+ modules from something that fits in your laptop bag.
See Your Power Draw in Real-Time
The “Reactor Core” display on the front panel shows exactly what your case is pulling. Dual 5-segment bar graphs visualize +12V and -12V current consumption in real-time.
What you can do with it:
- Spot which modules are power-hungry at a glance
- Catch transient spikes when patching
- Know when you’re approaching your power limit
- Debug power issues without pulling out a meter
Instant analog feedback - no lag, no guessing. Industrial aesthetic with matte black PCB and translucent light pipes.
Silent Power
Switching supplies can introduce audible whine and noise into sensitive analog circuits. The PDX-2 is designed to stay quiet.
How it achieves silence:
- 2.2 MHz switching frequency (far above audible range - no PSU whine)
- Multi-stage filtering with low-ESR polymer capacitors
- Inverting buck-boost topology for clean negative rail (not a noisy charge pump)
The result: clean voltage rails that won’t compromise high-gain stages, precision oscillators, or clock generators.
Your Modules Stay Safe
The PDX-2 includes a hardware sequencing interlock that prevents module damage during power-up.
What it does: The -12V rail won’t turn on until +12V is stable. This prevents “latch-up” failures that can destroy op-amp based modules during startup.
Protection systems:
- Short circuit shutdown - saves your modules from wiring mistakes
- Thermal shutdown - protects under extreme loads
- Reverse voltage clamps - guards against power bus errors
- TVS input suppression - handles voltage spikes from power sources
Power From Anywhere
Bring your case wherever there’s USB-C power:
- Coffee shop (your laptop charger)
- Studio (dedicated USB-C PD brick)
- On location (USB-C battery pack with 20V support)
- Live performance (share power with your laptop)
Just plug in any USB-C PD charger that supports 20V at 45W or higher (65W recommended for headroom). The PDX-2 negotiates the voltage automatically.
Flexible Connectivity
Output options:
- Screw terminals (rear): Direct wiring to bus boards with 18AWG wire
- 16-pin IDC header: Standard Eurorack connection
Use screw terminals for permanent installations with thick wire and low resistance. Use the IDC header for standard ribbon cables.
Technical Specifications
| Rail | Current Output | Enough For… |
|---|---|---|
| +12V | 3.0A continuous, 5A peak | 15+ VCOs or complex modules |
| -12V | 1.5A continuous | Balanced analog stages |
Total system power: 54W continuous
Physical:
- Width: 4 HP (20mm)
- Depth: 35mm (fits skiff cases)
- Switching frequency: 2.2 MHz (inaudible)
Status
Currently in final hardware validation. Expected release: Q2 2025.
What’s Included
- Conduit PDX-2 module (fully assembled and tested)
- M3 mounting screws (black oxide)
- Quick start guide
Note: USB-C PD power brick and cable sold separately. Minimum 45W with 20V support required (65W recommended for headroom). Most modern laptop chargers work perfectly.
Compatibility
Works with:
- Any USB-C PD charger supporting 20V (45W minimum, 65W recommended)
- Standard Eurorack 16-pin bus (Doepfer/Intellijel format)
- Skiff cases (35mm depth)
Tested with:
- Apple 61W/67W USB-C chargers (MacBook)
- Anker PowerPort Atom PD 60W+
- Dell/HP/Lenovo laptop chargers with USB-C PD
Compatible bus boards available separately.